Craftsman Lawn Mower User Manual. See Prices; Craftsman Lawn Mower 107.289860. Craftsman Gas Powered Riding Lawn Tractor Operator's Manual. Craftsman 30' Briggs & Stratton Silver 17.5 hp Side Rear Discharge Gas Powered Riding Lawn Tractor Operator's Manual. See Prices; Craftsman Lawn Mower 28903. Craftsman Lawn Tractor. View and Download CRAFTSMAN 9 owner's manual online. 18.5 HP, 42' Mower Electric Start Automatic Transmission. 9 Lawn Mower pdf manual download. LIMITED WARRANTY ON CRAFTSMAN RIDING EQUIPMENT For two (2) years from the date of purchase, if this Craftsman Riding Equipment maintained.
Attention! The text in this document has been recognized automatically. To view the original document, you can use the 'Original mode'.
Advertising
5. Connect suspension arms to rear
deck brackets and secure with retainer
springs.
springs.
6. Connect anti-sway bar to chassis
bracket and secure with retainer spring.
7. Install belt into electric clutch pulley
groove.
TO LEVEL MOWER HOUSING
Adjust the mower while tractor is parked
on level ground or driveway. Make sure
tires are properly inflated (See “PROD
tires are properly inflated (See “PROD
UCT SPECIFICATIONS” section of this
manual). If tires are over or underinflated,
manual). If tires are over or underinflated,
you will not properly adjust your mower.
SIDE-TO-SIDE ADJUSTMENT WITH
BUBBLE LEVEL
NOTE: If necessary, check side-to-side
NOTE: If necessary, check side-to-side
surface below tractor for level ness with a
long board and the bubble level.
• Using the lift lever, place mower in posi
tion where no part of the mower, includ
ing gauge wheels, is touching the ground.
• From left side of tractor, find the level
decal on top of mower and place bubble
level on decal as indicated.
• Mower is level side-to-side when bubble
is between the two lines in the bubble
level.
level.
• If adjustment is necessary, under left
hand footrest, turn lift link adjustment
nut (above yellow cap) in appropriate
nut (above yellow cap) in appropriate
direction to bring bubble between the
lines in the bubble level.
• Remove bubble level from mower and https://matterbrown309.weebly.com/nikon-sb-28-user-manual-pdf.html.
store in a safe place.
ALTERNATE SIDE-TO-SIDE
ADJUSTMENT METHOD
ADJUSTMENT METHOD
• Raise mower to its highest position.
• At the midpoint of both sides of mower,
• At the midpoint of both sides of mower,
measure height from bottom edge of
mower to ground. Distance “A” on both
mower to ground. Distance “A” on both
sides of mower should be the same or
within 1/4' of each other.
• If adjustment is necessary, make adjust
ment on one side of mower only.
• To raise one side of mower, tighten lift
link adjustment nut on that side.
• To lower one side of mower, loosen lift
link adjustment nut on that side.
NOTE: Each full turn of adjustment nut
will change mower height about 1/8'.
•
Recheck measurements after ad
justing.
Bottom Edge of
Bottom Edge of
23
FRONT-TO-BACK ADJUSTMENT
IMPORTANT: Deck must be level side-to-
IMPORTANT: Deck must be level side-to-
side. If the following front-to-back adjust
ment is necessary, be sure to adjust both
front links equally so mower will stay
level side-to-side.
To obtain the best cutting results, the
mower housing should be adjusted so
that the front is approximately 1/8' to 1/2'
lower than the rear when the mower is in
its highest position.
its highest position.
Check adjustment on right side of tractor.
Measure distance “D” directly in front of
and behind the mandrel at bottom edge of
mower housing as shown.
• Before making any necessary adjust
ments, check that both front links are
equal in length.
• If links are not equal in length, adjust
one link to same length as other link.
• To lower front of mower loosen nut “E”
on both front links an equal number of
turns.
turns.
• When distance “D' is 1/8' to 1/2'
lower at front than rear, tighten nuts “F” https://matterbrown309.weebly.com/ricoh-theta-s-camera-user-manual.html.
against trunnion on both front links.
• To raise front of mower, loosen nut “F”
from trunnion on both front links. Tighten
nut “E” on both front links an equal num
ber of turns. The two front links must
remain equal in length.
• When distance “D' is 1/8' to 1/2' lower
at front than rear, tighten nut “F” against
trunnion on both front links.
Craftsman Dyt 4000 Price
Recheck side-to-side adjustment.
Advertising
This manual is related to the following products:
Popular Brands
Popular manuals
Attention! The text in this document has been recognized automatically. To view the original document, you can use the 'Original mode'.
Advertising
LENGTH
TO REPLACE MOWER BLADE DRIVE
BELT
The mower blade drive belt may be re
Craftsman Dyt 4000 Troubleshooting
placed without tools. Park the tractor on
level surface. Engage parking brake.
BELT REMOVAL -
1. Remove mower from tractor (See “TO
REMOVE MOWER” in this section of
manual).
manual).
Craftsman Dyt 4000 For Sale
2. Work belt off both mandrel pulleys and
idler pulleys.
3. Pull belt away from mower.
BELT INSTALLATION -
1
.
2
.
3.
Work belt around both mandrel pulleys
and idler pulleys
and idler pulleys
Make sure belt is in all pulley grooves
and inside all belt guides.
Install mower (See “To Install Mower” Apple iphone 7 user guide pdf download.
in this section of this manual).
TO CHECK AND ADJUST BRAKE
Your tractor is equipped with an adjustable
Your tractor is equipped with an adjustable
brake system which is mounted on the
right side of the transaxle.
right side of the transaxle.
If tractor requires more than five (5) feet to
stop at highest speed in highest gear on a
level, dry concrete or paved surface, then
brake must be checked and adjusted.
brake must be checked and adjusted.
TO CHECK BRAKE
1. Park tractor on a level, dry concrete or
paved surface, depress clutch/brake
pedal all the way down and engage
parking brake.
pedal all the way down and engage
parking brake.
2. Disengage transmission by placing
freewheel control in “transmission dis
engaged” position. Pull freewheel con
trol out and into the slot and release so
engaged” position. Pull freewheel con
trol out and into the slot and release so
it is held in the disengaged position.
The rear wheels must lock and skid when
you try to manually push the tractor for
you try to manually push the tractor for
ward. If the rear wheels rotate, the brake
needs to be adjusted or the pads need to
be replaced.
be replaced.
TO ADJUST BRAKE
1.
3.
4.
5.
Depress clutch/brake pedal all the way
down and engage parking brake.
Measure distance between brake oper
ating arm and nut “A” on brake rod.
If distance is other than 1-9/16', loosen
jam nut and turn nut “A” until distance
becomes 1-9/16'. Retighten jam nut
against nut “A'.
against nut “A'.
Engage transmission by placing
freewheel control in “transmission
engaged” position.
engaged” position.
Road test tractor for proper stopping
distance as stated above. Readjust
if necessary. If stopping distance is
still greater than five (5) feet in highest
gear, further maintenance is neces
sary. Replace brake pads or contact a
gear, further maintenance is neces
sary. Replace brake pads or contact a
Sears or other qualified service center.
With parking brake “Engaged”
Do not touch this nut. If further brake
adjustment is necessary contact a Sears or
other qualified service center.
other qualified service center.
24
Advertising
This manual is related to the following products:
Popular Brands
Popular manuals